Prevent Pittsburgh Home Electrical Fires-Act Now!

Prevent Pittsburgh Home Electrical Fires-Act Now!

Inadequate electrical capacity is mainly due to increasing the number of devices that consume electricity in your Pittsburgh home like new heating and cooling equipment, frost free refrigerators, clothes dryers, water heaters, electric ranges and ovens, dishwashers, and other powerful electric motor driven tools and appliances. Below are some suggestions to prevent Pittsburgh home electrical fires!

As you add devices to your Pittsburgh home, the power supply may become inadequate. If you have indicators like fuses or circuit breakers tripping, or lights dimming, it is time to carefully look at your circumstances before equipment failure, fire, or other problems arise.

5 Causes of Inadequate Power in Your Pittsburgh Home

Commercial electricians Pittsburgh-PA; Best Electricians Near Me; Tatman Electric; Residential electricians Pittsburgh-PA; Electricians Pittsburgh-PA; Best Electricians Pittsburgh Tatman Electric; Residential lighting installation Pittsburgh-PA; Electrical Contractor Pittsburgh-PA; Wiring Pittsburgh-PA;; Whole House Wiring Pittsburgh-PA; Whole House Generator Installation Pittsburgh-PA; Rewiring Pittsburgh-PA; Service Panel Upgrade Pittsburgh-PA;

1.Limited Service Panel Capacity

When the overall demand from total electrical devices is greater than what the panel is able to supply, the main service panel will likely fail, frequently. Excess demand indicates that the panel rating is less than needed or the panel might be limiting capacity because it has no space left for more fuses or circuit breakers.

In either case it’s time to make a circuit map to calculate demand and compare it with the capacity of the main panel to supply. If you find the power demand is less than the capacity and there is no room for more breakers, then a sub-panel might be the answer. Conversely, if the overall demand is greater than the main panel ability to supply, then you will need a licensed Pittsburgh electrician to complete a Pittsburgh service panel upgrade.

2. Overloaded Circuits

Another use for the circuit map is to determine if demand on the circuits are greater than the amperage rating of the circuit controlling it. It is important to note peak demands of appliances that may draw more power on starting and create a power surge that trips the breaker.

A power surge that does not trip the breaker is indicated by lights dimming when an appliance turns on. Appliances that produce surges should have their own separate circuit designed to tolerate the surge. Also, a Pittsburgh whole house surge protector can help.

To prevent Pittsburgh home electrical fires do not exceed the safe amperage of the circuit. Blown fuses or tripped breakers indicate an overloaded circuit. Do not replace breakers with ones of higher amperage just because they fail. Instead run a new circuit from the main panel that is within the supply capacity.

3. Insufficient Number of Outlets

A general recommendation is to have at least one outlet for every 12 feet of wall, ground fault interrupted outlets in bathrooms and exterior walls, one outlet for each countertop in the kitchen, or as required by local Pittsburgh codes.

The most obvious indicator that more outlets are needed is when you start to use multi-outlet extension cords on a regular or permanent basis. Most low-cost extension cords are not designed to carry heavy amperage demanded of permanent wiring. Excess loads may cause overheating and fire.

Computer workstations can require outlets for more than two devices from a single dual receptacle wall circuit. Older CRT monitors and laser printers can cause surges when they are turned on. The best solution is to supply the required outlets on separate circuit(s) designed to exceed the demand. The next best option is to use a fused and surge protected uninterrupted power supply (UPS) to protect your equipment. UPS are now available for less than $100 and can protect your computer investment from power problems better than anything else. The less expensive power bars and extension cords run risks of equipment damage or fires if the circuit is overloaded.

4. Inadequate Feeder Lines

Older Pittsburgh houses may have original two-wire feed lines from the power company’s nearest utility pole. One of the wires is hot, delivering 110-115 volts and the other is neutral. Obviously, these lines will not power 240-volt appliances nor is the amperage likely able to power more than a few newer appliances at a time.

The electric company should replace the two-wire system with a three-wire system at their own expense. Since you will have to pay an Pittsburgh electrician to install a new service panel, use your circuit map and any expansion plans to determine future demand, then size the new panel capacity accordingly.

5. Overtaxed Transformer

In older high-density Pittsburgh neighborhoods electricity demands over time have increased. In some cases, the transformer serving the area may not have been increased to meet the growth in demand. Although the power companies are required to scale up supply according to demand, it is wise to check into the matter before paying to connect a larger service.

Electricians Pittsburgh; electrical contractors Pittsburgh-PA; residential electrical contractors; electrical contractor company Pittsburgh-PA; local electrical contractors;

In conclusion On Prevent Pittsburgh Home Electrical Fires

If you are concerned about your Pittsburgh home electrical system, contact Tatman Electric. As the best Electricians Pittsburgh PA, we can help make sure you and your family are safe. In addition, our family owned, and operated company guarantees 100% customer satisfaction and have maintained a 5 star Google rating for many years. Do not wait, contact Tatman Electric Today!